66922.63USD
53.05USD
1.32USD
0.09USD
2053.6USD
8.19USD
589.58USD
80.18USD
0.05USD
0.03USD
0.05USD
Video Upload Q&A Likes Trends
@Ada

The result shows there is not enough ASIC! Repair it.

What's the meaning of the L3+ singleboard test result
@Ada

The temp sensor model in test file configuration does not match the one in hashboard. Correct it.

L3+ single-board test-- temperature error
@Ada

The temp sensor model in test file configuration does not match the one in hashboard. Correct it.

L3+ single-board test-- temperature error
@Ada

Check the facility environment temprature, can not too low or too high. Try to keep the temprature above 0°C.

T17e always disconnections with the hashbaords
@Ada
Compare the voltage domains of CLK before and after to see if they are the same. Also, check the specific error reported by the hashboards. It's possible that 1.1V is within the normal range.
All peripheral CLK signals of S9 are high, around 1.1V. What could be the issue?
@Ada
The USB-TTL did not connected well to the tester. Check the wire connected to Ground.
What could be the problem causing frequent garbled output on the fixture?
@Ada
No. they can not be mixes. Different version with different specification.
Can 1397AD and 1397AG be mixed and used interchangeably?
@Ada
The pic program is failed. Re-program the PIC with the Pickit.
Update the official website firmware results in the hashrate as shown in this image. What is the problem?
@Ada
Replace the IO port and then test again.
The hashboard can pass the single-board test but chip 34 RI voltage only 1.3V.
@Ada
Check the temprature sensor IC U88, replace it. Then there are domain voltage 8.5V and all chips hashrate [114],Nounce[912].
All the chips have been tested, but temperature 0 and all chips' hashrate reported as [00].
@Ada
Check the temprature sensor IC U88, replace it. Then there are domain voltage 8.5V and all chips hashrate [114],Nounce[912].
All the chips have been tested, but temperature 0 and all chips' hashrate reported as [00].
@Ada
It is possible that either chip 56 or chip 57 is faulty, or there could be an issue with the 0.8V voltage supply.
S9 single-board test showed Nonce [0] from chip 56, why this happened?
PgUp...2425262728...PgDn
Recommend
@jaeeunni
Other Roles
@luisenriquerodriguezc
Individual Miner
@1adrianguster
Other Roles
@nelson3891
Other Roles
@aarnold0805
Individual Miner
@332caac9c0
Other Roles
Hot Topics
Lucky Miner LV07 Firmware
7129
See the below single-board test result. There are 8.4V,8.5V domain voltage, replacing chip 1 did not work.
6802
As shown in the picture below, T15 machine, 58, 59, 60 are all replaced, it still doesn’t work, what’s the problem.
6780
How To Install Bitmain S19 And S19j Pro Low Power Mode Firmware: Step-By-Step
6165
Lucky Miner Wi-Fi reconnect
5687
LTC Mining with Lucky Miner Lv06
5549
Back to firmware Lucky Miner Lvl 06: I need the www.bin file. Can someone help?
5174
Lucky miner v6
5085
Cannot access IP address lucky miner
5060
Lucky miner LV06 breakdown
4820
Hot download
Luckyminer LV06-V2.3.0_upgrade firmware 页面升级固件
1430
Luckyminer LV06 factory firmware V2.1.0 页面升级固件
616
Luckyminer Management Tool
588
Solo Miner_Lucky Miner User Guide LV05-LV08_20231215
411
Luckyminer LV07 Instruction and User Guide PC English
177
Luckyminer LV 07 Product Manual
141
Luckyminer LV06 ESP-Prog JTAG Debug Guide_Tool kit
139
SOLO Miner_Nerdminer USB Shape（V3）配置说明1107
136
IceRiver_MinerTool_English_V1.0.15 (1)
127
Luckyminer乐透机用户使用说明LV05-LV08(2023.12.15)
87

No. 199, Zhaojuesi South Rd, Chenghua District, Chengdu, Sichuan, China

No.14, Jian'an Rd, Bao An District, ShenZhen, GuangDong, China

+86 15390421113

minerfixesofficial@gmail.com

About Us Contact Us FAQ News
Bitaxe Project Bitaxe Github OSMU Official OSMU Discord Bitaxe Web Flasher
Privacy Policy Terms & Conditions
2022 Minerfixes - All Rights Reserved